7 Tips To Make The Best Use Of Your Peugeot Keys
Peugeot 208 Key Replacement
It is best to delegate the replacement of Peugeot keys 208 to auto locksmiths who have the necessary equipment and technical know-how. They can program and create keys faster and cheaper than a dealership.
A dead battery for your coin is most likely to be the cause if your key fob stops locking or unlocking doors. There are other reasons why the key may be malfunctioning.
Dead Coin Battery
A dead coin battery will stop your Peugeot 208 from locking and unlocking, as well as hindering it from starting the engine. In this case you'll need to employ the alternate method of starting described in your vehicle owner's manual.
The spark plugs could also be worn out. Spark plugs are what ignite the fuel to start the engine. However they have a finite life span. They will eventually break down in the event that they aren't utilized enough.
Luckily, there's an easy solution to this issue. Check the voltage of your battery using a multimeter. If it's below 11.5 Volts it is time to replace it. If the battery is corroded it is crucial to clean its contacts. This can be done by lifting the rubber covers that protect the two terminals on the battery and using a wire brush to remove any corroded areas of the battery. Then, reconnect the cables to the positive and negative poles.
Water Damage
If your 208 isn't starting and the battery is not empty, you must ensure that the spark plugs are working. You may find that they are dirty and don't spark. The spark plugs can be cleaned in a workshop.
Peugeot cars are equipped with a transponder style key that integrates with the car's immobiliser system. This ensures that only the correct key can start the engine. If the chip inside the Peugeot key is damaged, it won't send the correct signal to the vehicle.
This is a typical issue that is often caused by water damage. The KeyLab is especially prevalent in colder climates, as the vehicle could have been exposed to rain or snow. If this is the case, call a reputable auto locksmith who has all the tools and equipment needed to change the key's programming. They will also have the latest technology and the machinery needed to make a Peugeot 208 smart key. The process shouldn't take more than 15 minutes.
Faulty Battery Contacts
Peugeot replaced the transponder chips by introducing a new model that is based on electronic components that are mounted on a circuit board. This new system works well when it's new, however, over time, the circuit boards begin to wear out and stop functioning correctly.
This could prevent the immobiliser's function from being activated, meaning your vehicle will not start. If this is the case, it's a good idea get in touch with a Peugeot specialist or locksmith.
A common issue occurs when the battery of the key fob starts to fail. This causes the blade of the key to stop feeding into your lock. A locksmith in your car will replace the battery and cut a new blade for you. This is a quick solution.
Faulty Receiver Module
It could be that the receiver module is faulty in the event that your Peugeot key fob isn't working after being dropped on the floor, or exposed to a sudden downpour or accidentally washed. The receiver is responsible for sending radio frequency signals to an on-board computer, which is responsible for controlling the centralized locking system inside your Peugeot vehicle.
Rubber seals on the key fob stop water from getting to the electronic chip. However prolonged exposure to water may break through these seals, causing damage to the chip. Submerging the key fob into sea water at the beach or throwing it into the pool can be particularly damaging due to the high salt content.
If your Peugeot spare key fob isn't working You'll need the module replaced. This is only performed by a professional auto locksmith or Peugeot specialist. In contrast to other vehicles, Peugeot keys are protected by an exclusive immobilizer system that requires the correct coding to begin the engine. This is why it is imperative that you should only rely on an authorized Peugeot locksmith to create and program an alternative.
Computer on-board is not working properly
The computer on board of your Peugeot is responsible for many of the functions in your car including power windows and airbags. When something goes wrong with these systems, it will usually display a code indicating the problem. This code will be stored within the system until the problem is resolved. Usually, this will mean replacing the onboard computer.
The most frequent cause for the airbag warning light to illuminate is corrosion or loose connections within the sensor. This could be due to wear and tear, aging, or exposure to moisture and salt. It is crucial to get this issue addressed as soon as you can, as an airbag that is malfunctioning can be risky in the event of an accident.
If your Peugeot is showing a card that is not being detected error, the battery inside the key fob might be weak or dead. This will stop the key fob sending a signal to deactivate the immobilizer on your vehicle. Test this by pressing the unlock button on the key fob and then trying to start your car. If this fails then the battery on the key needs to be replaced.